specialistshaa.blogg.se

1. BEAR CCD 3000 SOFTWARE MANUALS
2. BEAR CCD 3000 SOFTWARE SERIAL
3. BEAR CCD 3000 SOFTWARE MANUAL
4. BEAR CCD 3000 SOFTWARE DOWNLOAD

BEAR CCD 3000 SOFTWARE DOWNLOAD

You can also sign up for email updates on the SEC open data program, including best practices that make it more efficient to download data, and SEC.gov enhancements that may impact scripted downloading processes. Please declare your traffic by updating your user agent to include company specific information.įor best practices on efficiently downloading information from SEC.gov, including the latest EDGAR filings, visit sec.gov/developer. Your request has been identified as part of a network of automated tools outside of the acceptable policy and will be managed until action is taken to declare your traffic. To allow for equitable access to all users, SEC reserves the right to limit requests originating from undeclared automated tools. When I open the slits, the peak should increase and broadens.Do you have friendly contact person at Horiba besides infojobinyvon -).Your Request Originates from an Undeclared Automated Tool

The spectrum should therefore have a baseline of 0 with a more or less narrow peak in the middle. Since the VIs do not crash, no erros occur and I get something similar to a spectrum I have the feeling that I am already so close.Īssistance.The CCD is mounted to a SPEX1404 double-monochromator and I checked a green emission line of a mercury lamp.

BEAR CCD 3000 SOFTWARE MANUAL

Well, in the manual of the controller several different CCDs are described, therefore I hoped they are compatible.

BEAR CCD 3000 SOFTWARE SERIAL

My ccd3000v controller has the same H07 printed on its identifier label.If you take a careful look into the VIs, you can see that the VIs load an.ini file in the CCD directory, as well as driver tabels.ĭear JW-WSI,The serial of my CCD-3000V controller ends with R16, so maybe there is a mismatch. If the signal increases the dip decreases until 220 and a peak within the dip is formed.If I take a 2D image most of the time a horzontal stripe pattern is shown.Both effects indicate a wrong readout or interpretation of the CCD.Are there specific CCD parameters the controller needsThank you very much for your help.ĭear NIHugo,I am not an expert on what CCD controller (either ccd3000 or ccd3000v) is the one that suits you best. I suppose you are not working with that thing after 7 years but maybe somebody else does.Good luck and have a nice day.JW.ĭear JW-WSI,I also have an ISA Spectrum One CCD and purchased recently a CCD-3000v controller for it.į09 but unfortanetly this is all information I have.It is already possible to acquire a spectrum but there is still something odd.Īs you can see in the attachement the baseline is around 900 and a weak signal results in a dip. There, the CCD is being initialized before doing anything.I attached the VIs to control the CCD. In order to bring the controller from Boot to Main send the command O200000 (now with the term char 00 or x00).Īfter probing with s you should get F now as a response.Now, use the CCDInit.VI in the LIBCCDsupllb directory and try to init the CCD or the Demo VIs in LIBCCDdemollb. If you get a b this means that your command could not be identified. It should reply with B for boot mode.After initialization it will respond with F.

BEAR CCD 3000 SOFTWARE MANUALS

Bear Ccd 3000 Software Free The Controllerīear Ccd 3000 Software Free The controller (the big box) has a heater circuit controlling the Temperature (Set to 140K).There are manuals and which should help you understanding the init process.Image acquisition (depending on the binning) takes with todays state of the art PCs and the desired (see manual 1) NI GPIB card up to 15 seconds with an integration time of 1000ms.Sending malformed commands (slightly wrong syntax) can crash the controller easily. Has anyone come up with a solution to this problem or has anyone come across it before Is it a hardware or software problem.I thought perhaps the vis were causing a problem with the ccd because it is Liquid Nitrogen cooled and this is not meant to be done unless the ccd is initialized, but there is no way to just initialize the ccd with labview that I can see.Īny thoughts Dear ShellpetalThe initialization of the camera has nothing to do with its cooling. So if I try to rerun the vi, or any other vi communicating to the ccd, it doesnt work. My SpectrumONE CCD has a baseline of about 1021 Counts1sec integration time. Bear Ccd 3000 Software By phanserfsecle1986 Follow | Publicīear Ccd 3000 Software Free The Controller